Leading 10 common forklift mishaps ， forklift procedure should take notice of these matters ！.

Don't undervalue the forklift at the office. If the procedure is not good, there will be serious mishaps in mins, and there are numerous crashes entailing forklifts.

Situation 1: The forklift cargo obstructed the vehicle driver's view, and the person ahead can not be discovered, leading to a rolling mishap.
Situation 2: In order to maintain the balance of the forklift when raising hefty items, the workers used their body weight as the counterweight, which almost created casualties.
Instance 3: The size of the forklift cargo exceeds the allowed width of the route and holds on the roadside rack, which nearly creates an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Instance 5: The forklift vehicle driver did not notice the pedestrian, and the pedestrian did not observe the forklift.
Case 6: The forklift raises the workers illegally, the forklift vehicle driver does not use the seat belt, the forklift lifter falls and the motorist is crushed when the forklift surrender.
Case 7: The forklift motorist did not wear a seat belt and dropped from the vehicle when it surrendered and was crushed.
Forklift operation should pay attention to these matters ：.

Beginning.
1. Before beginning, observe the environments, and after verifying that there are no barriers that hinder the security of driving, honk the horn first and afterwards begin.
2. For vehicles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) gauge have to be safe prior to beginning.
3. When the forklift starts with a tons, the vehicle driver should first verify that the lots is secure and reputable.
4. The beginning has to be slow and stable.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the pole must be slanted in reverse. .
2. Do not raise the fork expensive when driving. When getting in and leaving the job site or while driving, be careful that there will be no obstacles in the sky. When the load is traveling, the fork should not be raised too high, which will certainly impact the stability of the forklift. .
3. After unloading, the fork should be lowered to the normal driving setting before driving. .
4. When transforming, if there are pedestrians or lorries close by, the driving signal needs to be released initially. High-speed doglegs are restricted. High-speed sharp turns will certainly trigger the vehicle to shed side stability and tip over. .
5. When the forklift is downhill, it is strictly restricted to shut off the fire and slide, and it is prohibited to brake unexpectedly while driving with tons unless there are special circumstances.
6. When the forklift is running, it has to follow the web traffic rules in the factory and should maintain a certain safety and security distance from the vehicle ahead. .
7. When the forklift is running, the tons should remain in the most affordable setting that does not hinder the driving, and the gantry needs to be correctly slanted back. The load will not be increased other than when stacking or packing. .
8. The elevation of the tons have to not block the motorist's view. In special conditions, when the item impacts the forward vision, drive at a reduced rate when reversing.
9. It is prohibited to switch on the ramp, neither to drive throughout the ramp. .
10. The safe driving speed of the forklift in the factory area is 5 km/h, and it has to drive safely at a low speed when getting in the manufacturing workshop location. .
11. When the forklift is raised, raised or driven, it is forbidden for personnel to stand on the fork to hold items and play a stabilizing duty. .
12. If problems are found, they will be repaired and reported in a timely way, and they will certainly never ever run with ailments or conceal them.

loading and dumping.
1. When fork-loading items, the range in between both forks must be readjusted as required to make the tons of both forks well balanced and not skewed, and one side of the item ought to be against the shelf. .
2. It is prohibited to deal with a single Electric Forklift Truck for Warehouse fork or use a fork top or pull. In unique scenarios, safety and security warning signs must be established to advise surrounding pedestrians. .
3. In the process of loading and unloading items, the forklift needs to be stopped with the brake. .
4. The speed of the vehicle need to be sluggish and stable. Beware not to roll the wheels on the dunnage, so as not to extend the rolled things and harm individuals. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as possible under the lots, and it ought to be noted that the fork tip need to not touch other items or items. The load must be stabilized with marginal back tilt of the gantry so that the tons does not slide in reverse. The mast can be Stand-on Electric Pallet Stacker slanted forward a little when the load is reduced to permit simple positioning of the load and removal of the forks. .
6. It is prohibited to fork items at high speed and ram hard items with the fork head. .
7. When the forklift is functioning, it is forbidden for individuals to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overwhelming is banned, and it is prohibited to utilize forks to raise personnel to engage in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not allowed to utilize the brake inertia to slide, place, round or roll objects. .
10. It is not allowed to make use of forks to select, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Prior to leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the parking brake deal with to dead or depress the emergency brake switch.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the chauffeur does not leave the car's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance should be checked, and gas, lubing oil and air conditioning water must be added.
2. Check the safety and security efficiency of starting, running and braking.
3. Examine whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, inspect whether the stress and temperature level are normal.
5. After the forklift is running, the external leak must likewise be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You have to examine before leaving the car;.
2. When you run into somebody before you throughout driving, you should send a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight should be 0.3 m ~ 0.4 m in the air;.
5. The transforming should not be also sharp to prevent the propensity of "free turning";.
6. Adding and down the slope must be slow and uniform, and no switching on the incline is allowed.
7. Do not drive across the slope. When the slope is greater than 10%, the lorry ought to be driven in reverse when worsening;.
8. When the forklift personnel bring the goods and move on, if they encounter big or hefty items and most likely to the driver's line of vision, they must take the turning around workout
.
The "Eight Prohibitions" need to be adhered to in the procedure.
1. Single fork operation is not allowed.
2. It is not allowed to lift the goods for far away driving.
3. It is not enabled to get the goods by handing over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not enabled to utilize inertia force to pick up the goods.
6. It is not allowed to use stopping pressure to exile round or easy-to-roll things.
7. It is not permitted to bring individuals to service the pallet or fork, and it is strictly forbidden to stand under the fork after the fork is raised.
8. Do not drive side to side on inclines
.
Car park is not allowed under the following conditions.
1. Contours, narrow roads, railway crossings;.
2. Sections with a longitudinal incline above 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the section with the same size as the obstacle should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844